 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HMC539LP3 / 539LP3E 0.25 dB LSB GaAs MMIC 5-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 4.0 GHz v00.0605 Typical Applications Features 0.25 dB LSB Steps to 7.75 dB +/- 0.05 dB Typical Step Error Low Insertion Loss: 0.7 dB High IP3: +50 dBm Single Control Line Per Bit TTL/CMOS Compatible Control Single +5V Supply 6 ATTENUATORS - SMT The HMC539LP3 / HMC539LP3E is ideal for both RF and IF applications: * Cellular Infrastructure * ISM, MMDS, WLAN, WiMAX, WiBro * Microwave Radio & VSAT * Test Equipment and Sensors Functional Diagram 3x3 mm SMT Package General Discription The HMC539LP3 & HMC539LP3E are broadband 5-bit GaAs IC digital attenuators in low cost leadless surface mount packages. This single positive control line per bit digital attenuator utilizes an off chip AC ground capacitor for near DC operation, making it suitable for a wide variety of RF and IF applications. Covering DC to 4.0 GHz, the insertion loss is less than 0.7 dB typical. The attenuator bit values are 0.25 (LSB), 0.5, 1, 2, and 4 dB for a total attenuation of 7.75 dB. Attenuation accuracy is excellent at 0.05 dB typical step error. The attenuator also features a high IIP3 of +50 dBm. Five TTL/CMOS control inputs are used to select each attenuation state. A single Vdd bias of +5V is required. Electrical Specifications, TA = +25 C, With Vdd = +5V & Vctl = 0/+5V (Unless Otherwise Noted) Parameter Insertion Loss Attenuation Range Return Loss (RF1 & RF2, All Atten. States) Attenuation Accuracy: (Referenced to Insertion Loss) Input Power for 0.1 dB Compression Input Third Order Intercept Point (Two-Tone Input Power= 0 dBm Each Tone) Switching Characteristics DC - 4.0 GHz tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) 48 52 ns ns All States Frequency (GHz) DC - 1.5 GHz 1.5 - 3.0 GHz 3.0 - 4.0 GHz DC - 4.0 GHz DC - 3.0 GHz 3.0 - 4.0 GHz DC - 3.0 GHz 3.0 - 4.0 GHz 0.1 - 4.0 GHz 0.1 - 4.0 GHz Min. Typ. 0.7 1.0 1.3 7.75 25 20 (0.2 + 2% of Atten. Setting) Max. (0.2 + 4% of Atten. Setting) Max. 28 50 Max. 1.0 1.3 1.7 Units dB dB dB dB dB dB dB dB dBm dBm 6 - 164 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC539LP3 / 539LP3E 0.25 dB LSB GaAs MMIC 5-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 4.0 GHz Return Loss RF1, RF2 Insertion Loss 0 -0.5 INSERTION LOSS (dB) RETURN LOSS (dB) -10 -1 -1.5 -2 -2.5 -40 -3 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) -45 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) +25 C +85 C -40 C v00.0605 (Only Major States are Shown) 0 -5 6 0.25 dB 0.5 dB 2 dB 1 dB -20 -25 -30 -35 Normalized Attenuation (Only Major States are Shown) 0 NORMALIZED ATTENUATION (dB) -1 -2 0.25 -4 -5 -6 -7 -8 -9 -10 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) -0.5 0 1 2 3 4 5 6 7 8 ATTENUATION STATE (dB) BIT ERROR (dB) -3 3 GHz 4 GHz 40 MHz Bit Error vs. Attenuation State 0.5 0 -0.25 1 GHz 100 MHz 500 MHz 2 GHz Bit Error vs. Frequency (Only Major States are Shown) 0.35 0.3 0.25 0.2 BIT ERROR (dB) 0.15 0.1 0.05 0 -0.05 -0.1 -0.15 -0.2 -0.25 0 7.75 dB 2 dB 4 dB 1 dB 0.25 dB 0.5 dB Relative Phase vs. Frequency (Only Major States are Shown) 20 15 RELATIVE PHASE (deg) 10 5 0 -5 -10 0.25-1 dB 7.75 dB 4 dB 2 dB -15 -20 0.5 1 1.5 2 2.5 3 3.5 4 4.5 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 6 - 165 ATTENUATORS - SMT -15 I.L.dB 4 dB 7.75 dB HMC539LP3 / 539LP3E 0.25 dB LSB GaAs MMIC 5-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 4.0 GHz Worst Case Step Error Between Successive Attenuation States v00.0605 6 STEP ERROR (dB) 0.25 0.2 0.15 0.1 0.05 0 -0.05 -0.1 -0.15 -0.2 -0.25 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) ATTENUATORS - SMT Bias Voltage & Current Vdd = +5.0 Vdc 10% Vdd (VDC) +4.5 +5.0 +5.5 Idd (Typ.) (mA) 3.3 3.5 3.7 Truth Table Control Voltage Input V1 4 dB High High High V2 2 dB High High High High Low High Low V3 1 dB High High High Low High High Low V4 0.5 dB High High Low High High High Low V5 0.25 dB High Low High High High High Low Attenuation State RF1 - RF2 Reference I.L. 0.25 dB 0.5 dB 1 dB 2 dB 4 dB 7.75 dB Control Voltage State Low High Note: Vdd = +5V Bias Condition 0 to +0.8V @ -5 uA Typ. +2.0 to + 5.0 Vdc @ 30 uA Typ. High High Low Low Any combination of the above states will provide an attenuation approximately equal to the sum of the bits selected. 6 - 166 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC539LP3 / 539LP3E 0.25 dB LSB GaAs MMIC 5-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 4.0 GHz v00.0605 Absolute Maximum Ratings RF Input Power (DC - 4.0 GHz) Control Voltage Range (V1 to V5) Bias Voltage (Vdd) Channel Temperature Continuous Pdiss (T = 85 C) (derate 12.0 mW/C above 85 C) Thermal Resistance Storage Temperature Operating Temperature ESD Sensitivity (HBM) +29 dBm (T = +85 C) -1V to Vdd +1V +7.0 Vdc 150 C 0.781 W 83 C/W -65 to +150 C -40 to +85 C Class 1A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 6 ATTENUATORS - SMT Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number HMC539LP3 HMC539LP3E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] 539 XXXX 539 XXXX [2] [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 6 - 167 HMC539LP3 / 539LP3E 0.25 dB LSB GaAs MMIC 5-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 4.0 GHz Pin Descriptions v00.0605 6 ATTENUATORS - SMT Pin Number 1 Function Vdd Description Supply Voltage. This pin is DC coupled and matched to 50 Ohm. Blocking capacitors are required. Select value based on lowest frequency of operation. These pins should be connected to PCB RF ground to maximize performance. External capacitor to ground is required. Select value for lowest frequency of operation. Place capacitor as close to pins as possible. Interface Schematic 2, 11 RF1, RF2 3, 9, 10 N/C 4-8 ACG1 - ACG5 12 - 16 V1 - V5 See truth table and control voltage table. GND Package bottom has an exposed metal paddle that must be connected to RF Ground. Application Circuit Recommended Component Values C1, C2 C3 C4 R1 - R5 100 pF 10% 1,000 pF 10% 330 pF 10% 100 Ohm 10% 6 - 168 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC539LP3 / 539LP3E 0.25 dB LSB GaAs MMIC 5-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 4.0 GHz v00.0605 Evaluation PCB 6 ATTENUATORS - SMT List of Materials for Evaluation PCB 110078 [1] Item J1 - J2 J3 - J9 C1, C2 C3 C4 R1 - R5 U1 PCB [2] Description PCB Mount SMA Connector DC Pin 100 pF Capacitor, 0402 Pkg. 1000 pF Capacitor, 0402 Pkg. 330 pF Capacitor, 0402 Pkg. 100 Ohm Resistor 0402 HMC539LP3 / HMC539LP3E Digital Attenuator 110076 Evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 6 - 169 |
Price & Availability of HMC539LP3
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |